SMM Morning Comment For SHFE Base Metals (September 23)

게시됨: Sep 23, 2024 09:51
출처: SMM
Last Friday evening, LME copper opened at $9,552/mt. After a slight initial decline, it rose to a high of $9,574/mt, then fell all the way down to $9,468/mt near the close.

SHANGHAI, Sep 23 (SMM) –

Copper

Market Concerns Over US Economic Recession Persisted, Copper Prices Slightly Declined [SMM Copper Morning Comment]

Last Friday evening, LME copper opened at $9,552/mt. After a slight initial decline, it rose to a high of $9,574/mt, then fell all the way down to $9,468/mt near the close. It slightly rebounded at the end, finally closing at $9,486/mt, a drop of 0.56%. Trading volume reached 18,000 lots, and open interest was 275,000 lots. Last Friday evening, the most-traded SHFE copper contract 2410 opened and peaked at 75,790 yuan/mt, then fell all the way down to 75,190 yuan/mt near the close. It slightly rebounded at the end, finally closing at 75,480 yuan/mt, a drop of 0.38%. Trading volume reached 32,000 lots, and open interest was 124,000 lots. On the macro side, since the US Fed initiated monetary policy easing, the US dollar has fluctuated repeatedly. Coupled with the lower-than-expected hawkish stance of the Bank of Japan last Friday, the yen came under pressure, and the US dollar index rebounded. Additionally, in a speech last Friday, US Fed Governor Waller indicated that if the job market deteriorates, a further 50 basis points rate cut might be considered. The market then adopted a cautious attitude, and concerns over a US economic recession persisted. Under this sentiment, major European stock indices collectively closed lower, and copper prices followed suit. On the fundamentals side, last Friday, due to typhoon weather, some traders reported that the pickup of imported goods was hindered, leading to a tight supply of spot copper cathode. Holders of the goods maintained firm spot premiums. On the consumption side, with the rise in copper prices last week, downstream buyers were highly cautious, and procurement demand was very strong. This week, coupled with pre-National Day stocking demand, inventory is expected to continue its downward trend. In terms of prices, supported by downstream consumption demand, copper prices are expected to fluctuate upward today.

Aluminum

The US Fed's stance on a rate cut in November remains uncertain; short-term aluminum prices are expected to fluctuate upward [SMM Aluminum Morning Comment]

SMM, Sep 23: Last Friday night, the most-traded SHFE aluminum 2411 contract opened at 19,980 yuan/mt, reaching a high of 20,000 yuan/mt and a low of 19,805 yuan/mt, and closed at 19,845 yuan/mt, down 225 yuan/mt, a decrease of 1.12%. On the previous trading day, LME aluminum opened at $2,536.5/mt, hit a high of $2,551/mt and a low of $2,478/mt, and closed at $2,486/mt, down $53.5/mt, a decrease of 2.11%.

On the macro front, the US Fed's stance on a rate cut in November remains uncertain, with the probabilities of a 50BP and 25BP cut being nearly equal. The market is awaiting the release of the US Fed's employment and inflation data this week. Meanwhile, the domestic LPR rate remains unchanged, slightly dampening domestic macro sentiment. On the fundamentals side, domestic aluminum market supply saw a slight increase, alumina showed upward fluctuations due to tight supply, and domestic aluminum costs remained high. Under the influence of the September-October peak season, aluminum downstream weekly operating rates remained stable, and downstream consumption showed steady improvement. However, caution is needed regarding the negative impact of overseas tax policies on domestic aluminum processing enterprises. Aluminum social inventory is still in a destocking cycle, with good supply-demand performance in September and October. Overall, given the short-term favorable macro front and stable fundamentals, the aluminum market is expected to fluctuate upward in the short term.

Lead

Lead Ingot Inventory Accumulation Intensified, Future Lead Prices to Watch for National Day Stockpiling Expectations [SMM Lead Morning Comment]

Last Friday, LME lead opened at $2,081/mt. During the Asian session, LME lead fluctuated upward, reaching an intraday high of $2,097.5/mt, a new high in nearly one and a half months. However, entering the European session, the US dollar index rose, coupled with an increase in LME lead inventory, causing LME lead to reverse and fall. The decline expanded during the night session, with LME lead giving up all daytime gains and finally closing at $2,042/mt, down 1.94%.

Last Friday, the most-traded SHFE lead 2410 contract opened at 16,520 yuan/mt. After the Mid-Autumn Festival, lead ingot inventory increased daily. SHFE lead quickly fell after opening, hitting a low of 16,320 yuan/mt and finally closing at 16,340 yuan/mt, down 1.8%. Its open interest was 33,860 lots, a decrease of 2,445 lots from the previous trading day.

Macro-wise, China did not cut interest rates, with the 1-year and 5-year LPRs remaining unchanged in September. US Fed Governor Waller noted that inflation slowed faster than expected, leading him to join the 50 basis point rate cut camp. Governor Bowman explained her dissenting vote, citing concerns about inflation and that a 50 basis point cut might be seen as prematurely declaring victory over inflation. Goldman Sachs indicated that two key voting members suggested the US Fed might slow the pace of rate cuts, making November uncertain. Additionally, weekend clashes between Israel and Lebanese militants intensified.

Fundamentally, after the Mid-Autumn Festival holiday, lead ingot inventory accumulation intensified both domestically and internationally. Domestic downstream enterprises gradually resumed normal production. Moving forward, we need to focus on the customary stockpiling actions of downstream enterprises before the National Day holiday. If consumption meets expectations, lead prices could potentially reach 17,000 yuan/mt. Conversely, we need to monitor the supply of scrap and the cost support from secondary lead.

Zinc

Hints of More Basis Points Rate Cuts, LME Zinc to Fluctuate Downward [SMM Zinc Morning Comment]

SMM, Sep 23: Last Friday, US Fed Governor Waller hinted at additional 50 basis points rate cuts; British media reported that Israel plans to conduct ground operations in Lebanon; Trump rejected Harris's invitation for another TV debate; a large-scale port strike is imminent, posing a major threat to the US supply chain; the fifth meeting of the China-US Economic Working Group was held; the CSRC revised and issued regulations on risk control indicators for securities companies.

Last Friday, LME zinc opened at $2,933.5/mt. Initially, LME zinc fluctuated rangebound around the daily moving average, then moved above it and peaked at $2,955/mt. By the European trading session, LME zinc fell back to fluctuate rangebound around the daily moving average, then SHFE zinc fluctuated downward in a stepwise manner below the daily moving average and hit a low of $2,866.5/mt. By the end of the session, LME zinc slightly moved up to fluctuate rangebound around $2,875/mt. During this period, LME zinc broke above the daily moving average but quickly fell back, closing down at $2,867/mt, a drop of $72.5/mt or 2.47%. Trading volume increased to 116,000 lots, and open interest decreased by 3,211 lots to 240,000 lots. Last Friday, LME zinc recorded a bearish candlestick with no lower shadow, with the upper Bollinger Bands forming resistance and the 10/60-day moving averages providing support below. LME social inventory decreased by 650 mt to 256,150 mt, a drop of 0.25%. Currently, with the US Fed Governor hinting at more 50 basis points rate cuts and about 45,000 workers at 36 US ports planning to strike on October 1, LME zinc was expected to fluctuate downward.

Last Friday, the most-traded SHFE zinc 2411 contract opened at 23,905 yuan/mt. Initially, with shorts increasing positions, SHFE zinc briefly fluctuated rangebound around the daily moving average and peaked at 23,920 yuan/mt. It then fluctuated downward below the daily moving average and hit a low of 23,620 yuan/mt. Subsequently, with shorts reducing positions, SHFE zinc's center of gravity slightly moved up to fluctuate rangebound around 23,700 yuan/mt, closing down at 23,700 yuan/mt, a drop of 310 yuan/mt or 1.29%. Trading volume decreased to 69,340 lots, and open interest increased by 898 lots to 101,000 lots. Last Friday, SHFE zinc recorded a bearish candlestick, with the daily K-line center of gravity moving downward, the upper Bollinger Bands forming resistance, and the 10/60-day moving averages providing support below. Currently, the supply side output remains low, and the demand side is also in a weak state. With both supply and demand weak, SHFE zinc was expected to fluctuate downward.

Tin

SHFE tin prices fell during the night session, some downstream enterprises placed orders [SMM Tin Morning News]

SMM, September 23: Last Friday, the most-traded SHFE tin contract closed at 258,660 yuan/mt in the night session, down 1,370 yuan/mt, a decrease of 0.53%. During the early session last Friday, the premiums and discounts quoted by trading companies for various domestic tin ingot brands did not change much compared to recent days. Specifically, small brand tin ingots were quoted at premiums of 0-500 yuan/mt against the SHFE 2410 contract, delivery brand prices were quoted at premiums of 200-700 yuan/mt against the SHFE 2410 contract, Yunnan Tin brand was quoted at premiums of 200-800 yuan/mt against the SHFE 2410 contract, and imported tin brands were quoted at discounts of 200-700 yuan/mt against the SHFE 2410 contract. Last Friday morning, tin prices surged significantly, and most downstream and end-user enterprises adopted a wait-and-see attitude, with only a few downstream enterprises restocking as needed. Most trading companies saw scattered transactions. Overall, the spot market transactions were relatively quiet last Friday.

Nickel

Last week, nickel prices fluctuated upward, mainly due to macro boosts. Macro front, after the US Fed cut interest rates by 50 basis points, combined with Fed Chairman Powell's remarks about the risk reduction of a US economic recession, short-term market risk appetite increased, leading to a fluctuation upward in nickel prices. Fundamentally, the current main speculation point remains on nickel ore. The approval of Indonesia's RKAB is still pending, but with market expectations for increased nickel ore supply, the enthusiasm for purchasing Philippine ore has declined. This indirectly reflects that current market concerns about tight nickel ore supply from Indonesia have eased compared to before. From the overall supply and demand of primary nickel, the September-October peak season for NEVs and traditional stainless steel industries did not meet expectations, causing upstream raw material prices, including NPI and nickel salts, to continue to decline. In the upstream intermediate products sector, the continuous production and release of hydrometallurgical and pyrometallurgical intermediate products have exacerbated the oversupply. Given the unfavorable fundamentals, nickel prices may face upward pressure. In the short term, while nickel prices are boosted by macro factors to fluctuate upward, the weak fundamentals suggest caution against the risk of nickel prices declining. It is expected that SHFE nickel will operate in the range of 122,000-127,000 yuan/mt this week.

데이터 출처 설명: 공개 정보를 제외한 모든 데이터는 SMM이 공개 정보, 시장 커뮤니케이션 및 SMM 내부 데이터베이스 모델을 기반으로 가공한 것입니다. 본 자료는 참고용이며 의사결정 권고를 구성하지 않습니다.

문의 사항이 있거나 자세한 정보를 원하시면 아래로 연락해 주시기 바랍니다: lemonzhao@smm.cn
리서치 보고서 열람 방법에 대한 자세한 내용은 아래로 문의하시기 바랍니다:service.en@smm.cn
관련 뉴스
ACG 게디크테페 황화물 확장 프로젝트, 첫 구리·아연 정광 생산; 2026년 말까지 완전 생산 목표
13시간 전
ACG 게디크테페 황화물 확장 프로젝트, 첫 구리·아연 정광 생산; 2026년 말까지 완전 생산 목표
더 보기
ACG 게디크테페 황화물 확장 프로젝트, 첫 구리·아연 정광 생산; 2026년 말까지 완전 생산 목표
ACG 게디크테페 황화물 확장 프로젝트, 첫 구리·아연 정광 생산; 2026년 말까지 완전 생산 목표
ACG Metals는 9월 1일 튀르키예 소재 Gediktepe 광산에서 8월 31일 첫 구리 정광을 생산했다고 발표하며 증산 단계에 돌입했다고 밝혔다. 회사는 처리량을 점진적으로 늘리고 플랜트 성능을 최적화하여 2026년 말까지 완전 가동을 목표로 하고 있다. Gediktepe의 정상 상태 연간 생산 목표는 구리 환산 2만~2만 5천 톤이다. 전체 발표문에는 해당 광산이 2026년 8월 첫 아연 정광을 생산했다는 내용도 포함되었으나, 구체적인 날짜와 생산량은 공개되지 않았다. SMM은 2026년 해당 광산의 아연 정광 내 아연 함유량을 약 1만~1만 5천 톤으로 추정했다.
13시간 전
[ SMM 분석 ] 19개 구리 제련소의 2026년 반기 보고서 한눈에 보기
13시간 전
[ SMM 분석 ] 19개 구리 제련소의 2026년 반기 보고서 한눈에 보기
더 보기
[ SMM 분석 ] 19개 구리 제련소의 2026년 반기 보고서 한눈에 보기
[ SMM 분석 ] 19개 구리 제련소의 2026년 반기 보고서 한눈에 보기
13시간 전
MMG, 보츠와나 코에마카우 확장 지원 위해 6,400만 달러 규모 장비 주문
15시간 전
MMG, 보츠와나 코에마카우 확장 지원 위해 6,400만 달러 규모 장비 주문
더 보기
MMG, 보츠와나 코에마카우 확장 지원 위해 6,400만 달러 규모 장비 주문
MMG, 보츠와나 코에마카우 확장 지원 위해 6,400만 달러 규모 장비 주문
에피록이 MMG 리미티드와 광산 계약업체인 차이나 화예, 23MCC로부터 보츠와나 코에마카우 구리 광산 확장을 지원하기 위한 지하 채굴 장비 주문을 약 6억 1천만 크로나(6,400만 달러) 규모로 수주했다. 이번 주문에는 갱도 굴착 드릴, 생산 드릴, 케이블 볼팅 장비, 로더, 지하 광산 트럭과 함께 원격 제어 시스템, 예비 부품, 교육, 현장 기술 지원이 포함된다. 이 장비는 MMG가 진행 중인 코에마카우 확장을 지원할 예정이며, 이를 통해 정광 내 구리 금속 연간 생산 능력을 약 6만 톤에서 13만 톤으로 늘리는 것이 목표다. 이 프로젝트에는 연산 450만 톤 규모의 새로운 처리 공장 건설이 포함되어 총 처리 능력을 800만 톤 이상으로 끌어올리게 되며, Zone 5 North, Mango, Zeta North-East 개발도 함께 진행된다. 확장 프로젝트의 첫 구리 정광 생산은 2028년 상반기로 예상된다. 에피록은 새로운 지하 장비의 인도가 2026년 4분기에 시작되어 2028년 2분기까지 완료될 예정이며, 이는 확장 일정과 대체로 일치한다고 밝혔다. 주문된 장비에는 부머 갱도 굴착 드릴, 심바 생산 드릴, 케이블텍 케이블 볼팅 장비, 스쿱트램 로더, 마인트럭 지하 트럭이 포함되며, 일부 장비는 자동화 및 원격 제어 운전이 가능하도록 구성된다. 이번 장비 주문은 이미 승인된 코에마카우 확장의 또 다른 실행 이정표로, 새로운 생산 목표가 아니다. 조달이 진행되고 장비 인도가 2028년 2분기까지 예정된 가운데, 프로젝트는 MMG가 계획한 정광 내 구리 생산 능력 연간 13만 톤 달성을 향해 계속 진전되고 있다. 이번 확장은 보츠와나 칼라하리 구리 벨트에서 코에마카우의 구리 생산 능력을 대폭 확대하려는 계획을 의미한다.
15시간 전