SMM Analysis: SHFE Aluminum Recorded Two Days of Gains amid Rising Downstream Operating Rates and Extended Destocking

게시됨: May 27, 2022 17:08 (GMT+8)
출처: SMM
SHANGHAI, May 27 (SMM) - SHFE aluminium closed up 1.22% at 20,775 yuan/mt today.

SHANGHAI, May 27 (SMM) - SHFE aluminium closed up 1.22% at 20,775 yuan/mt today.

The average operating rate across major aluminium processing enterprises increased 2.7 percentage points from a week ago to 61.8% this week, but has not recovered to levels seen before the Labour Day holiday. The operating rates in the aluminium extrusion sector rose thanks to improved pandemic situation. The aluminium wire and cable industry also performed well on the back of sufficient orders on hand. The operating rates in the primary and secondary alloy sectors did not increase significantly due to slow recovery of auto industry. Although the operating rates of aluminium plate/sheet, strip and foil producers remained stable, enterprises are more pessimistic about new orders in the future. In terms of different regions, except for an increase in operating rates in Shandong, Jiangsu, Zhejiang and Shanghai, and Hunan, which were driven by the improvement of the pandemic, operating rates in other regions did not change much.

As of May 26, aluminium ingot social inventory across eight major markets in China totalled 936,000 mt, down 29,000 mt from a week ago and 50,000 mt lower than the end of April. Aluminum billet inventory fell 4.61% to 130,100 mt.

Due to the production cuts and capacity replacement during the month, the growth rate of domestic operating aluminium capacity has slowed down. The ratio of aluminium liquid output of smelters in north-west China has increased. These have contributed to the destocking of aluminium ingot social inventory. However, the market also needs to pay attention to the inventory of aluminium intermediate products.

This week, the downstream demand side remained stable as a whole, and the production of construction extruders in some regions has resumed, but the demand for aluminium from automotive and construction sectors was still relatively weak. The improvement in domestic consumption and destocking will provide support to aluminium prices, but macroeconomic pessimism may prevent aluminium prices from rising significantly.

데이터 출처 설명: 공개 정보를 제외한 모든 데이터는 SMM이 공개 정보, 시장 커뮤니케이션 및 SMM 내부 데이터베이스 모델을 기반으로 가공한 것입니다. 본 자료는 참고용이며 의사결정 권고를 구성하지 않습니다.

문의 사항이 있거나 자세한 정보를 원하시면 아래로 연락해 주시기 바랍니다: lemonzhao@smm.cn
리서치 보고서 열람 방법에 대한 자세한 내용은 아래로 문의하시기 바랍니다:service.en@smm.cn
관련 뉴스
허난 이루이의 첨단 알루미늄 압연기가 생산을 시작하며 고급 시장 성장을 목표로 한다
6시간 전
허난 이루이의 첨단 알루미늄 압연기가 생산을 시작하며 고급 시장 성장을 목표로 한다
더 보기
허난 이루이의 첨단 알루미늄 압연기가 생산을 시작하며 고급 시장 성장을 목표로 한다
허난 이루이의 첨단 알루미늄 압연기가 생산을 시작하며 고급 시장 성장을 목표로 한다
9월 20일, 허난 이루이 신소재 기술 유한공사의 연간 72만 톤 알루미늄 기반 신소재 스마트 제조 프로젝트의 후판 조압연기가 정식으로 가동되었다. 총 투자액 15억 위안 규모의 이 프로젝트는 기존 공장 부지를 활용하여 국제적으로 앞선 "1+4" 열간 연속 압연 라인을 구축했으며, 푸셔식 재가열로 등 업계 선도적인 알루미늄 가공 설비를 갖추고 있다. 또한 압연력, 온도 등 핵심 생산 파라미터를 실시간으로 모니터링하고 동적으로 조절할 수 있는 산업용 사물인터넷 시스템을 구축하여 고급 알루미늄 제품의 품질 안정성을 효과적으로 보장하고 고부가가치 제품의 시장 점유율을 지속적으로 확대하고 있다.
6시간 전
기니, 글렌코어와 광업 협력 확대…수익 및 산업화 증대 목표
6시간 전
기니, 글렌코어와 광업 협력 확대…수익 및 산업화 증대 목표
더 보기
기니, 글렌코어와 광업 협력 확대…수익 및 산업화 증대 목표
기니, 글렌코어와 광업 협력 확대…수익 및 산업화 증대 목표
기니는 글렌코어와의 협력을 알루미나 정제, 에너지, 금, 비철금속 분야로 확대할 계획이며, 광업 수익 확대, 광물 자원의 현지 가공 및 산업화 촉진, 중국·중동 및 기타 지역 시장 및 국제 광산 기업과의 협력 강화를 목표로 한다.
6시간 전
딩펑알루미늄, 캄보디아에서 2단계 착공…연간 생산능력 20만 톤 목표
6시간 전
딩펑알루미늄, 캄보디아에서 2단계 착공…연간 생산능력 20만 톤 목표
더 보기
딩펑알루미늄, 캄보디아에서 2단계 착공…연간 생산능력 20만 톤 목표
딩펑알루미늄, 캄보디아에서 2단계 착공…연간 생산능력 20만 톤 목표
9월 21일, 디항그룹 산하 딩펑알루미늄제조(캄보디아)유한회사 2단계(A3 프로젝트) 기공식이 거행되었다. 캄보디아 캄퐁참주 6번 도로 특별경제구역에 위치한 딩펑알루미늄은 고급 합금 알루미늄 봉, 고급 알루미늄 프로파일 및 신에너지 자동차 부속 제품의 연구개발과 생산을 주력으로 하며, 용해·주조, 압출, 양극산화, 심가공, 정밀가공, 표면처리를 아우르는 전 공정 생산라인과 설비를 갖추고 있다. 2단계가 완전 가동되면 연간 생산능력은 20만 톤, 연간 생산액은 최대 7억 달러에 달할 전망이다. 2단계(A3 프로젝트)에는 24,340㎡ 규모의 신에너지 자동차 가공공장(단층 철골구조), 15,291㎡ 규모의 압출공장, 그리고 사무동, 경비실, 배전실 등 부대시설이 포함될 예정이다.
6시간 전