[SMM analysis] the operating rate of aluminum sheet and strip increased significantly in March compared with the previous month, and fell back in April into an established fact.

게시됨: Apr 13, 2020 19:01 (GMT+8)
SMM conducted a survey of the aluminum plate and strip market in March and learned that the average weighted operating rate of China's aluminum plate and strip industry was 62.25% in March, up 13 percentage points from the previous month, down more than 10 percentage points from the same period last year, and is expected to fall slightly to 61 per cent in April 2020.

SMM conducted a survey of the aluminum plate and strip market in March and learned that the average weighted operating rate of China's aluminum plate and strip industry was 62.25% in March, up 13 percentage points from the previous month, down more than 10 percentage points from the same period last year, and is expected to fall slightly to 61 per cent in April 2020.

Source: SMM

At the beginning of March, most of the production conditions of plate and strip enterprises in the industry returned to normal, and some enterprises were still in a state of semi-shutdown due to less orders and slow rework of employees. The start-up rate in March was higher than that in February, mainly due to the fact that most of the plate and belt enterprises in the industry were on holiday in February due to the influence of the epidemic situation, and the start-up rate was relatively low in March, while in March, with the gradual resumption of work and resumption of production, the start-up rate was also relatively higher, and some of the order production plans delayed during the February holiday were released in March, resulting in a significant increase in the start-up rate in March.

Last year, it is still worse than last year, and the terminal consumer market is limited by the weak performance of the epidemic. According to the order category, the performance of building plate and 3C electronic material is relatively stable, the performance of packaging orders such as tank material is relatively weak, the worst is automobile plate, the domestic automobile industry is depressed in March, and foreign car factories in Japan, Europe and the United States and Europe and the United States have stopped production, which has a direct impact on the export of relevant automobile aluminum and domestic trade orders. In addition, most of the aluminum plate and strip enterprises reported that the severity of the epidemic abroad gradually escalated in the middle and late March, and export orders were significantly affected. Customers have withdrawn orders and delayed pick-up of shipments, or customers have been affected by the foreign epidemic and then reduced their orders for cooperation with themselves. In the aspect of finished product inventory, most of the enterprises feedback that their finished product inventory is high, mainly due to the slow pick-up of end customers, and there is obvious pressure on their own funds.

As far as April is concerned, the current corporate feedback is not optimistic. First of all, the export proportion of large plate and strip enterprises in Shandong, Henan, and Fujian is relatively high, between 30% and 50% as a whole, and about 20% of the indirect exports of small and medium-sized enterprises also exist. However, the epidemic situation has not yet appeared an inflection point overseas, and there is even a further serious trend. Overseas countries have adopted measures to seal off countries and ports, and it seems to have become an established fact that export orders continue to decline from April to May. Against the background of weak domestic trade orders, Foreign trade has made matters worse, and the start-up rate in April is expected to be lower than in March.

(SMM Xuman 021-51595898)

 

데이터 출처 설명: 공개 정보를 제외한 모든 데이터는 SMM이 공개 정보, 시장 커뮤니케이션 및 SMM 내부 데이터베이스 모델을 기반으로 가공한 것입니다. 본 자료는 참고용이며 의사결정 권고를 구성하지 않습니다.

문의 사항이 있거나 자세한 정보를 원하시면 아래로 연락해 주시기 바랍니다: lemonzhao@smm.cn
리서치 보고서 열람 방법에 대한 자세한 내용은 아래로 문의하시기 바랍니다:service.en@smm.cn
관련 뉴스
【SMM 알루미늄 플래시 뉴스】전 세계 알루미늄 캔 재활용률 76%로 상승, 2030년까지 80% 목표
3분 전
【SMM 알루미늄 플래시 뉴스】전 세계 알루미늄 캔 재활용률 76%로 상승, 2030년까지 80% 목표
더 보기
【SMM 알루미늄 플래시 뉴스】전 세계 알루미늄 캔 재활용률 76%로 상승, 2030년까지 80% 목표
【SMM 알루미늄 플래시 뉴스】전 세계 알루미늄 캔 재활용률 76%로 상승, 2030년까지 80% 목표
글로벌 음료 캔 순환 연합이 발표한 2026 글로벌 음료 용기 재활용 데이터셋에 따르면, 전 세계 알루미늄 캔 재활용률이 74.8%에서 76%로 증가했으며 회수율은 77%에 달해 다른 주요 음료 포장재보다 앞서 있는 것으로 나타났다. PET병의 회수율과 재활용률은 각각 69%와 54%로 기록되었고, 유리병은 56%와 51%로 집계되었다. 이 데이터셋은 각 포장재별 전 세계 판매량의 최소 84%를 대표하는 시장을 대상으로 한다. 업계는 2030년까지 사용된 음료 캔의 재활용률 80% 달성을 목표로 하고 있으며, 이후 2050년까지 100%에 근접하는 것을 목표로 삼고 있다. 인도, 인도네시아, 사우디아라비아, 튀르키예, 나이지리아는 회수 및 재활용 시스템의 추가 개선이 필요한 주요 신흥 음료 시장으로 주목받고 있다.
3분 전
【SMM Aluminum Flash News】Cameroon’s Minim Martap Bauxite Project Faces Funding Setback, First Shipment Delayed
4분 전
【SMM Aluminum Flash News】Cameroon’s Minim Martap Bauxite Project Faces Funding Setback, First Shipment Delayed
더 보기
【SMM Aluminum Flash News】Cameroon’s Minim Martap Bauxite Project Faces Funding Setback, First Shipment Delayed
【SMM Aluminum Flash News】Cameroon’s Minim Martap Bauxite Project Faces Funding Setback, First Shipment Delayed
Canyon Resources’ Minim Martap bauxite project in Cameroon faces fresh uncertainty after AFG Bank Cameroon suspended further drawdowns from the project’s syndicated financing facility on August 24, pending a review of its development schedule, financial model and economic assumptions. Canyon has confirmed that Phase 1 will not meet its previous timetable and has withdrawn its Q4 2026 first-shipment target, with no new date announced. Minim Martap has a mineral resource of around 1.1 billion tonnes and an ore reserve of 144 million tonnes, averaging approximately 51% alumina and 2% silica. Canyon held around AUD 31 million in cash at the end of July, while approximately $75 million had already been drawn from the CFA 82 billion syndicated facility. The company is reducing non-essential spending while reassessing the project’s development and funding pathway.
4분 전
【SMM 알루미늄 속보】캐터필러, 인도에서 광업 및 인프라용 신규 장비 3종 출시
4분 전
【SMM 알루미늄 속보】캐터필러, 인도에서 광업 및 인프라용 신규 장비 3종 출시
더 보기
【SMM 알루미늄 속보】캐터필러, 인도에서 광업 및 인프라용 신규 장비 3종 출시
【SMM 알루미늄 속보】캐터필러, 인도에서 광업 및 인프라용 신규 장비 3종 출시
캐터필러는 바우마 코넥스포 인디아 2026에서 Cat 355 유압 굴삭기, Cat D5 도저, Cat 120 GC 모터 그레이더를 출시하며 광업, 대형 인프라, 도로 건설 분야를 겨냥했다. Cat 355는 C13B 엔진과 전자유압 시스템을 탑재했으며 최대 4.5m³ 버킷 옵션을 제공하고, Cat D5는 170마력 C7.1 엔진과 4.3m³ 블레이드를 갖췄다. Cat 120 GC는 주로 도로 유지보수와 정밀 정지 작업용으로 설계됐다. 이번 출시로 캐터필러는 인도 광업 및 인프라 부문을 위한 장비 라인업을 더욱 확대했다.
4분 전