[SMM analysis] the operating rate of aluminum sheet and strip increased significantly in March compared with the previous month, and fell back in April into an established fact.

Publicado: Apr 13, 2020 19:01 (GMT+8)
SMM conducted a survey of the aluminum plate and strip market in March and learned that the average weighted operating rate of China's aluminum plate and strip industry was 62.25% in March, up 13 percentage points from the previous month, down more than 10 percentage points from the same period last year, and is expected to fall slightly to 61 per cent in April 2020.

SMM conducted a survey of the aluminum plate and strip market in March and learned that the average weighted operating rate of China's aluminum plate and strip industry was 62.25% in March, up 13 percentage points from the previous month, down more than 10 percentage points from the same period last year, and is expected to fall slightly to 61 per cent in April 2020.

Source: SMM

At the beginning of March, most of the production conditions of plate and strip enterprises in the industry returned to normal, and some enterprises were still in a state of semi-shutdown due to less orders and slow rework of employees. The start-up rate in March was higher than that in February, mainly due to the fact that most of the plate and belt enterprises in the industry were on holiday in February due to the influence of the epidemic situation, and the start-up rate was relatively low in March, while in March, with the gradual resumption of work and resumption of production, the start-up rate was also relatively higher, and some of the order production plans delayed during the February holiday were released in March, resulting in a significant increase in the start-up rate in March.

Last year, it is still worse than last year, and the terminal consumer market is limited by the weak performance of the epidemic. According to the order category, the performance of building plate and 3C electronic material is relatively stable, the performance of packaging orders such as tank material is relatively weak, the worst is automobile plate, the domestic automobile industry is depressed in March, and foreign car factories in Japan, Europe and the United States and Europe and the United States have stopped production, which has a direct impact on the export of relevant automobile aluminum and domestic trade orders. In addition, most of the aluminum plate and strip enterprises reported that the severity of the epidemic abroad gradually escalated in the middle and late March, and export orders were significantly affected. Customers have withdrawn orders and delayed pick-up of shipments, or customers have been affected by the foreign epidemic and then reduced their orders for cooperation with themselves. In the aspect of finished product inventory, most of the enterprises feedback that their finished product inventory is high, mainly due to the slow pick-up of end customers, and there is obvious pressure on their own funds.

As far as April is concerned, the current corporate feedback is not optimistic. First of all, the export proportion of large plate and strip enterprises in Shandong, Henan, and Fujian is relatively high, between 30% and 50% as a whole, and about 20% of the indirect exports of small and medium-sized enterprises also exist. However, the epidemic situation has not yet appeared an inflection point overseas, and there is even a further serious trend. Overseas countries have adopted measures to seal off countries and ports, and it seems to have become an established fact that export orders continue to decline from April to May. Against the background of weak domestic trade orders, Foreign trade has made matters worse, and the start-up rate in April is expected to be lower than in March.

(SMM Xuman 021-51595898)

 

Declaración de Fuente de Datos: Excepto la información disponible públicamente, todos los demás datos son procesados por SMM basándose en información pública, comunicación de mercado y confiando en el modelo de base de datos interna de SMM. Son solo para referencia y no constituyen recomendaciones para la toma de decisiones.

Para cualquier consulta o para obtener más información, por favor contacte: lemonzhao@smm.cn
Para más información sobre cómo acceder a nuestros informes de investigación, contacte con:service.en@smm.cn
Noticias relacionadas
【SMM Noticias rápidas sobre el aluminio】La tasa mundial de reciclaje de latas de aluminio sube al 76 %, con la meta del 80 % para 2030
hace 3 minutos
【SMM Noticias rápidas sobre el aluminio】La tasa mundial de reciclaje de latas de aluminio sube al 76 %, con la meta del 80 % para 2030
Leer más
【SMM Noticias rápidas sobre el aluminio】La tasa mundial de reciclaje de latas de aluminio sube al 76 %, con la meta del 80 % para 2030
【SMM Noticias rápidas sobre el aluminio】La tasa mundial de reciclaje de latas de aluminio sube al 76 %, con la meta del 80 % para 2030
El conjunto de datos de reciclaje de envases de bebidas de 2026 publicado por la Alianza Global de Circularidad de Latas de Bebidas muestra que la tasa global de reciclaje de latas de aluminio ha aumentado del 74,8 % al 76 %, mientras que la tasa de recolección alcanzó el 77 %, manteniéndose por delante de otros formatos principales de envases de bebidas. Las botellas de PET registraron tasas de recolección y reciclaje del 69 % y 54 %, respectivamente, en comparación con el 56 % y el 51 % de las botellas de vidrio. El conjunto de datos cubre mercados que representan al menos el 84 % de las ventas globales de cada formato de envase. La industria tiene como objetivo una tasa de reciclaje del 80 % para las latas de bebidas usadas para 2030, seguida de una meta de acercarse al 100 % para 2050. India, Indonesia, Arabia Saudita, Turquía y Nigeria se encuentran entre los mercados emergentes de bebidas destacados por necesitar mejoras adicionales en sus sistemas de recolección y reciclaje.
hace 3 minutos
【SMM Aluminum Flash News】Cameroon’s Minim Martap Bauxite Project Faces Funding Setback, First Shipment Delayed
hace 4 minutos
【SMM Aluminum Flash News】Cameroon’s Minim Martap Bauxite Project Faces Funding Setback, First Shipment Delayed
Leer más
【SMM Aluminum Flash News】Cameroon’s Minim Martap Bauxite Project Faces Funding Setback, First Shipment Delayed
【SMM Aluminum Flash News】Cameroon’s Minim Martap Bauxite Project Faces Funding Setback, First Shipment Delayed
Canyon Resources’ Minim Martap bauxite project in Cameroon faces fresh uncertainty after AFG Bank Cameroon suspended further drawdowns from the project’s syndicated financing facility on August 24, pending a review of its development schedule, financial model and economic assumptions. Canyon has confirmed that Phase 1 will not meet its previous timetable and has withdrawn its Q4 2026 first-shipment target, with no new date announced. Minim Martap has a mineral resource of around 1.1 billion tonnes and an ore reserve of 144 million tonnes, averaging approximately 51% alumina and 2% silica. Canyon held around AUD 31 million in cash at the end of July, while approximately $75 million had already been drawn from the CFA 82 billion syndicated facility. The company is reducing non-essential spending while reassessing the project’s development and funding pathway.
hace 4 minutos
【SMM Noticias rápidas sobre aluminio】Caterpillar lanza tres nuevas máquinas en India para aplicaciones de minería e infraestructura
hace 4 minutos
【SMM Noticias rápidas sobre aluminio】Caterpillar lanza tres nuevas máquinas en India para aplicaciones de minería e infraestructura
Leer más
【SMM Noticias rápidas sobre aluminio】Caterpillar lanza tres nuevas máquinas en India para aplicaciones de minería e infraestructura
【SMM Noticias rápidas sobre aluminio】Caterpillar lanza tres nuevas máquinas en India para aplicaciones de minería e infraestructura
Caterpillar ha lanzado la excavadora hidráulica Cat 355, el tractor de cadenas Cat D5 y la motoniveladora Cat 120 GC en bauma CONEXPO India 2026, orientados a aplicaciones de minería, infraestructura pesada y construcción de carreteras. La Cat 355 cuenta con un motor C13B y sistema electrohidráulico con opciones de cucharón de hasta 4,5 m³, mientras que la Cat D5 está impulsada por un motor C7.1 de 170 hp y cuenta con una hoja de 4,3 m³. La Cat 120 GC está diseñada principalmente para aplicaciones de mantenimiento de carreteras y nivelación de acabado. Estos lanzamientos amplían aún más la oferta de equipos de Caterpillar para los sectores de minería e infraestructura de la India.
hace 4 minutos